Discounted: Shop-vac 906-87-19 Universal Tool Adapter

Shop-vac 906-87-19 Universal Tool Adapter

Shop-vac 906-87-19 Universal Tool Adapter
Shop-Vac(R) Corporation is the recognized world leader in wet/dry vacuum cleaners. For more than 40 years, Shop-Vac(R) Corporation has manufactured innovative, high quality vacuum cleaners and accessories. Shop-Vac(R) Corporation offers the most complete line of vacuum cleaners and accessories available for consumer, industrial and commercial applications.The Shop-Vac universal tool adapter allows you to connect virtually any power tool with an exhaust port to a Shop-Vac wet/dry vacuum. With a 1-to-2-inch diameter range, the adapter custom fits onto any vacuum cleaner’s standard hose end. Made of soft, pliable plastic, the adapter can be cut to many different diameters.

  • Used to adapt virtually any power tool to work with all Shop-Vac(R) brand wet/dry vacuums
  • Black
  • Genuine Shop Vac Part
  • Easy to Use
  • Rust Free Plastic

List Price: $ 14.99

Price: $ 8.59

Related Power Tool Accessories Products

Question by Vigor: What accessories do I need for a car amplifier and subs?
I am going to buy a car and subs, but dont know what wires, tools, etc I need.

Best answer:

Answer by The Old SoundMan
The amplifier you need depends on what other speakers you intend to use with the subwoofer, what sort of sound pressure levels you are likely to be running at etc. You could use a four channel amplifier and drive your left and right splits off channels 1&2 then use channel 3&4 in bridged mono to drive your sub.

As the Dual sub is rated at 4 ohms that may work out well as long as the amplifier will drive 4 ohms in bridged mono mode. (Most should)

Crutchfield also lists this amplifier which should do the job.
http://www.crutchfield.com/p_489HA1040/P…

Car amplifier power ratings can generally be taken with a grain of salt.
The RMS power rating is the most important along with the recommended load impedance. If you drive a 4 ohm speaker with an amplifier rated for maximum power at 2 ohms you will only get half the power delivered to the speakers.

If the speaker impedance is lower than the amplifier rating you can damage the amplifier and the speakers if you drive it hard!

You will need 4 or 6 guage power cable to power the amplifier, a 60A inline fuse, speaker cable to run from the amp to the sub and to the L&R splits, diagonal wire cutters, screwdrivers, stanley knife, insulation tape, straightened coathanger wire for pulling speaker and power leads through firewall and under carpets etc, 12v test lamp, multimeter.

good luck,

Old Sound Man

Know better? Leave your own answer in the comments!

Click here for more Power Tool Accessories info.

Permalink to ‘Discounted: Shop-vac 906-87-19 Universal Tool Adapter’

Category: Product Reviews

4 Responses to “Discounted: Shop-vac 906-87-19 Universal Tool Adapter”

  1. desert rat "jeff baby"
    47 of 47 people found the following review helpful
    4.0 out of 5 stars
    Want measurements on this adapter? I did., January 16, 2012
    By
    desert rat “jeff baby” (California, USA) –

    Amazon Verified Purchase(What’s this?)
    This review is from: Shop-vac 906-87-19 Universal Tool Adapter (Tools & Home Improvement)

    I knew I was guessing as I could not find the exact measurements for this adapter’s capacities. I am research oriented and checked multiple websites, product listings and reviews to try to learn the sizes offered by this unit. I could not find them given anywhere so I bought this with fingers crossed.

    Here are the measurements of the adapter by Shop Vac 90687. OD are 2.5″ 2.0″ 1.5″ 1.25″ and 1.0″. (Most manufacturers cite the OD ((Outer diameter)) when listing a measurement).
    The measurements for the inner diameter were 2.3″ 1.5″ 1.25″ 1.0″ and .75″. By the way, the overall length before you cut it down at all is 6.75″. I cut off the last 2 smaller sections and the length was reduced to 4.35″. Either length may not work for your needs if space is tight.

    Ultimately this unit did not work out for my application. Now that you have the measurements posted, I hope this helps some of you as it is going to work if your requirements align. I will keep mine since I cut it to measure and hope to use it on something in the future.

    Help other customers find the most helpful reviews

    Was this review helpful to you? Yes
    No

  2. Paul "rivercitykid"
    38 of 40 people found the following review helpful
    5.0 out of 5 stars
    You won’t get hosed on this one, March 19, 2001
    By
    Paul “rivercitykid” (Albuq., NM United States) –

    This review is from: Shop-vac 906-87-19 Universal Tool Adapter (Tools & Home Improvement)

    I have used a couple of these devices to connect the dust port on tools to vacume hose. Funny how there are standard sizes of dust collection and vacume hoses, but every tool seems to have a dust collection port that is in some odd size. Nothing fits. This adaptor gets in between the odd sizes of tools and standard size of hose. You can easily trim this adaptor to fit either an inside diameter or outside diameter of the adaptor. Like I have said before, it does what it says it will do.

    Help other customers find the most helpful reviews

    Was this review helpful to you? Yes
    No

  3. Fred Anonymous Smith
    19 of 19 people found the following review helpful
    5.0 out of 5 stars
    Effective Solution In Most Cases, September 17, 2010
    By
    Fred Anonymous Smith (Huntsville. AL) –

    Amazon Verified Purchase(What’s this?)
    This review is from: Shop-vac 906-87-19 Universal Tool Adapter (Tools & Home Improvement)

    I’ve tried several step adaptors, but this Shop-Vac 9068700 universal tool adapter has worked most often. I’m now back to purchase two or three more.

    This adaptor fits over (or replaces) a 2 1/2-inch exhaust port and can be cut, stretched, or clamped to fit nearly any vacuum cleaner hose between 5/8-inch to just over 2-inches. The rubber-like material can be stretched (occasionally with some effort) to fit tight connections. I’ve even fit this over exhaust ports the same size. Soap with a little water (and rubber gloves to improve grip) can help with really tight connections. Loose connections can be secured wih hose clamps. Hoses can fit either inside and over the various incremental sections. Unused sections can be cut away with a razor knife (box cutter, etc) or power tool (bandsaw, etc).

    In one application, I replaced a bolt-on exhaust port with this adaptor (that’s what the four screw holes are for) and then cut the oppposite end to fit my vacuum hose. With other applications, the large ends were simply slipped over existing exhaust ports, with the opposite ends again cut to fit my vacuum hose. Finally, several were used to add exhaust ports to home-built projects (downdraft table, etc).

    This adapter may not impress others or attract girlfriends, but it often does wonders with vacuum cleaner hose connections.

    Help other customers find the most helpful reviews

    Was this review helpful to you? Yes
    No

  4. camaroguy1981

    u need a power wire a ground wire remote wire they uaually sell all the wiring in a kit but if u want a real thick power wire they will that seperate a probably an inline fuse

Leave a Reply

%d bloggers like this: